All posts tagged: Fireplace

BREAKING: My Kitchen has a Fireplace!

demo4

I decided to just tear the band-aid off and fully demo my kitchen. I’m not positive that this was the smartest idea but given that the pantry was already torn out, two of four walls were down to the studs, the ceiling was gone, and the floor was some mix of original tongue-and-groove subfloor in some places, a first layer of plywood subfloor in other places, and a second layer of plywood subfloor with my black VCT flooring in other places, it felt stupid to be holding onto what was left! Which was really just a wall with some cabinets and a kitchen sink.

So now I really don’t have a kitchen, but whatever! At least now I can easily-ish and efficiently-ish level out the subfloor and put in a new floor, run my new plumbing, electric, and gas (YES, GAS! SEE YA, 40 year old electric stove!), insulate, and start putting things back together. I don’t honestly know how far I can stretch my dollars so a real finished kitchen with fancy things like permanent countertops might still be a ways away, but I’m hopeful that I can at least at least get the foundation in place and achieve something usable in the near-ish future. I’m dealing with a lot of -ish right now because I don’t totally know how this is all going to play out. At least I have plenty of time to plan? Which sounds absurd since I’ve been mentally planning this kitchen renovation for over three years. It still changes on a nearly daily basis.

chimney2013

Now here’s a throwback! This is my kitchen after living in my house for about 2 days. Note the brick-patterned vinyl wallpaper! That always struck me as funny since the entirety of that wallpapered part is, in fact, a plastered-over brick chimney. When I bought the house, this chimney was being used to very unsafely vent a hot water heater, but now the chimney doesn’t do anything.

One thing I’ve known and continue to know for sure is that the layout of this space is completely changing. The stove will no longer sit on this wall where there’s very little room for any prep space adjacent to it. The sink is moving, all the cabinets are moving, even the exterior door is moving! I’ll share full plans ASAP when I can pull a sketchup together.

2chimney2013

Anyway, first order of business was tearing off the vinyl wallpaper and taking out the drop ceiling. Behind it was this color-blocked plaster which I actually kind of loved the look of, leaving aside how nasty it was.

3chimney2013

After lots of paint and stuff, things started to look more like this! See that round hole in the chimney up toward the ceiling? That’s a vent hole for a wood stove, which is how I always assumed this room was originally heated. This house was built before radiators, so the original heat sources would have been in fireplaces and wood stoves.

This is how I was planning to leave things until a bigger kitchen renovation down the road when I could expose the brick, but then I got subway-tile-happy. I thought I’d be working with this kitchen longer than I did (I was expecting it to be about 5-10 years, but the whole side-of-house-restoration and its effect on the kitchen have bumped this priority up significantly!), so at the time doing the extra subway tile seemed like a nice way to enhance this space in the short term. It was. I liked it. No regrets.

basementfireplace

I’m sorry to say I don’t have a good picture of it, but here’s what’s happening directly below, in the basement. See how there’s a whole fireplace (which is actually quite beautiful) down here? I thought this indicated that this room in the basement was probably the original kitchen—which could still be true, as there are also remnants of an early plumbing system). Fireplace in the basement, wood or coal stove in the kitchen, and possibly another one in the room above it was what I always imagined.

4chimney2015

All of this is to say that I felt pretty certain that the only thing behind my subway tile and the plaster would be a solid brick wall, which I always planned to expose during the eventual kitchen renovation. I had this idea that maybe I’d try to preserve my subway tile and expose just the brick above it (and probably paint it), and I also had this idea that I’d place a longer, lower radiator across the width of the chimney, which I hoped would look great and heat the room better.

demo1

Trying to preserve the subway tile was kind of not worth it because the chimney had been furred out on one side so that the kitchen sink would fit snugly in that space, and it definitely wasn’t the best tiling job in the world to begin with, and I did want to see what the whole chimney looked like before committing to keeping half of it tiled, and…who cares, tear it all down.

demo2

This is what my 27th birthday looked like last week! My life is so cute.

demo3

But look, brick! The plaster came off the brick REALLY very easily using just a hammer and a pry bar. The key is to take your time because old bricks will break if you get impatient and start hammering away too hard. The hardest part is just hauling the debris out of the house, because plaster is super heavy stuff! I’ve brought about 2,500 pounds of plaster to the dump just in the past two weeks.

demo4

So I’m chipping away at plaster and tile and all of a sudden I see THIS! WHATTTTTTT. That’s pretty unmistakably the curved top of an actual firebox!! I was amazed. I was stunned. I’d long accepted that all I was uncovering was an old and probably pretty brick wall with a hole in it for a wood stove. I literally had to take a break to get my breathing under control.

demo5

Before long…OH HELLO! Obviously the whole thing was bricked over at some point, I guess when they switched to the wood stove set-up, abandoned the fireplace, and plastered the chimney? I don’t really know a ton about this so I have some research to do.

clean-out

You can see this in the third photo of this post, but there was this funny cut-out in the plaster toward the floor, lined with metal and with this flimsy metal cover. I took the cover off exactly once when I was  painting this wall, saw a dark pit of despair with a bunch of dirt and leaves and stuff, and put the cover back on and tiled around it because I didn’t know what else to do! I figure it’s basically a clean-out for anything that might come down though the chimney or soot from the wood stove.

demo7

Now that I could see that it was part of a whole firebox, I removed the metal lining and started tearing out brick!

demo6

Inside was pretty nasty! The old soot and stuff was packed in a few feet high, along with some broken glass (??), a bunch of leaves, brick fragments…nothing fun, just yucky.

chimney2016

But now! LOOK! LOOK! LOOOOOOOK! In case you couldn’t tell, I’m VERY excited about this discovery. One of my big goals with the kitchen is to make it look and feel more in keeping with the original details found in most of the rest of the house, so being able to uncover this fabulous existing feature is SUPER motivating.

As to what I’ll actually do with it, I don’t know yet! I’ll definitely be adding a hearth stone in front of it (not sure what…I guess conceivably it could either be a slab of something, continuation of the brick, or tile?). The firebox is only a foot deep, so in terms of making it at all functional, I think gas logs might be the way to go here. I’ll call a chimney person to see what can/should be done in terms of a cap at the top of the chimney, probably a new liner, I guess some kind of damper to keep the heat from all escaping out the flue…like I said, research time! I’m just still so shocked and excited that it’s even there that my mind can’t process all this activity at once.

My kitchen is going to be the best kitchen, folks. CAN. NOT. WAIT.

A Mantel Makeover for Angie’s List

I love a good mantel. I love a good challenge. I love crazy old tiles. What do all of these things have in common? It’s this fireplace! Boom:

before_straightonview

Sometimes I get asked to do bloggy things that aren’t for my own site, which is typically not my jam because I’m usually stupid busy and not paying enough attention to my own site to worry about someone else’s, but I made an exception when Angie’s List came at me with a mantel makeover challenge. I didn’t have a mantel that was a good candidate for the project, but I knew somebody who did, and this seemed like the perfect excuse to get my grubby hands on it.

beforeangled

This mantel belongs to John, who just bought this incredible circa-1900 house in Kingston. I helped him find the house! I told him to buy it! He bought it! He moved from New Jersey! This poor house has undergone some serious wreck-ovation over the years, but it has amazing potential and John is totally committed to restoring it, so of course I am all over this. He doesn’t really need a full-on designer and he doesn’t really need a turnkey project manager, so I’m stepping into sort of a consultant role as he moves through this renovation…helping him design and plan and coordinate and execute and make this house the showpiece it’s supposed to be.

ANYWAY. This was exciting because there wasn’t anything technically wrong with this mantel or this room…ya know, it could have been fine but ugly for a few years and everyone would have lived. Often with old houses there’s a pretty big gap between the fun and pretty and the finance-draining and decidedly unsexy, and the latter is what has to take precedence. So it was nice to have a great excuse to bump this wayyyyy up the list (like, literally before “unpack your boxes”) because the “before” made me so sad. Somebody painted the original tiles with either a textured paint or some kind of plaster overlay stuff, and those 1973 built-ins—replete with fluorescent lighting, crappy wood, gold-crackled mirrored tiles, and an enormous soffit overhead connecting the two sides—had no business in this magnificent living room.

stripping-process

First order of business was demo-ing the built-in stuff and starting the longggg and arduous stripping process. Between John and I, it probably took about 30 hours of scraping and scrubbing and picking and cursing and beer-drinking to get down to the bare tile. We stripped the fireplace in two parts because I actually lacked confidence that the paint stripper would be able to penetrate whatever was causing the texture, so I didn’t want to waste and make a huge mess only to figure out that we had to come up with a plan B.

wall-stripping

We did not have to come up with a plan B, though, because the paint stripper worked SO well. When the room was almost done, I had John go back to the little nooks and crannies with one of those 15 minute jelly-like strippers and a bunch of tiny tools like dental picks to really get everything off.

Now, I love that tile. I’m guessing a lot of people won’t love that tile, but I don’t care! John had a mini freak-out when we first started really exposing it, but I didn’t care then either. I think it’s glazed terra cotta, with a burnt-orangey-red and green color combo that is admittedly extremely hard to work with. I kind of can’t blame whoever painted it because with the wrong wall color and stuff in the room, I can see it looking pretty awful. John even asked whether we’d be better off painting it again, but I veto’d that plan because I’m super bossy and unpleasant generally, and you just don’t paint old tile. You just don’t. Don’t do it. But really, this is a pretty awesome original detail in a house that is missing a fair amount of original detail, so in my mind it wasn’t even a choice.

By the way, that pile of wood in the foreground is all the lumber that comprised the old built-ins. I’m a crazy person, but hear me out. My basic rule with lumber is that if it’s over about 6″ long, it gets kept. This is why my garage looks like a disorderly lumber yard, but it’s also why I barely ever have to buy wood anymore! It’s environmentally responsible and economical—you don’t necessarily think of 1x6s or something being a large expense in a project, but wood is pricey! And it’s not as nice as it used to be, anyway! Even though these built-ins were only from the 1970s, it was pretty interesting to compare the totally standard 1-by lumber to what’s commonly available today—the not-even-that-old stuff we tore out is so much denser and heavier and contains fewer knots. Even the furring strips were pretty nice! All of it got de-nailed and set aside and treated like gold.

wall-stripping

After the major mantel-stripping was over, I applied the Peel Away to the surrounding wall, too. The texture was carried up this part of the wall, and it seemed potentially easier and better to try to get down to the bare plaster before repairing and skim-coating the wall than just covering it with a skim-coat. The Peel Away worked really well for this, too, and didn’t damage the plaster at all (it’s commonly used for this, but I’m not sure how other types of strippers would react). Then it was just a matter of doing a nice skim-coating job and light sanding and we were good to go!

salvage-wood

Dudes, I’m a woodworker now. Basically. Or something. If you want to become a crazy salvage wood person like myself, invest in a decent table saw—I have no idea what I’d do without mine! This way you can rip your recycled boards into your own dimensions precisely and easily, and for some reason I find that VERY fun. I have a Porter Cable table saw which has been going strong for a few years and works great.

during_cabinetboxes

I used a combination of salvaged and some new wood to make some new built-ins, the basis of which is basically a plywood box on a 2×6 base. Someday I’ll learn some fancy joining techniques, but on this day I went with what I read on some weird message board a long time ago about building cabinet boxes—that a combo of plywood, wood glue, drywall screws, and finish nails is actually pretty comparable to nice rabbeted joint, except significantly simpler and faster. Then it was just a matter of putting them in place, furring out the sides and top to make them appear super beefy, and throwing a lot of salvaged (and some new) trim and stuff to make it look all classy and finished.

after_logs

Not too shabby, right? I feel pretty proud of how these wood storage cubbies turned out, especially because of how little new material went into them. It was a lot of fun! We plan to add shallower bookshelves going up to the ceiling on top, but there wasn’t enough time to do that and get the post to Angie’s List in time, so I’ll post an update when that happens.

Let’s see that before photo again, just for funsies:

before_straightonview

Annnndddd:

afterstraightonview

I love that wall color for the tile! It’s kind of a charcoal-y navy with some green undertone, and I think it works super well. John originally wanted light grey walls in here, but I’m glad he let me talk him into going super dark after we both saw the fireplace tile and felt like our light grey samples weren’t doing it any favors.

after_smooth-wall

That egg-and-dart detail is just so amazing. I love that every one of these tiles is completely unique, a little irregular, and just so perfectly-imperfect. So worth the ridiculous time commitment and blisters.

after_angled2

SO! Turns out I was not the only blogger that signed up for this, and Angie’s List made it a CONTEST. WITH A CASH PRIZE. WHICH I WOULD VERY MUCH ENJOY HAVING.

I wrote a whole other blog post for Angie’s List with different pictures and text and more detail about the process and products, which you should go check out here! And then you should go vote for my project here! I guess you can vote once every 24 hours, and voting is open for a few more weeks, so go to town! BRING HOME THE BACON, FOLKS!

Building the Faux Fireplace!

header

Since I’ve been dealing with something of a forced hiatus from working on the cottage due to the gas/heat issues, I’ve taken the opportunity to refocus on my own renovation. Remember that? A lot of people in my life have assumed that since I’ve taken on a whole other renovation, my own house must be close to completion. VERY FALSE. I could try to list all the things I still need to do, but it would take you like three days to read and give me a panic attack, so just take my word for it. It’s a lot.

wallbefore

I’ve talked before about the room at the front of our house, which was likely originally a parlor. It’s the first room t0 the right when you walk in the front door (you can look at a floor plan here), and essentially rounds out the side of this floor I’ve been working on since we bought the house—first with the kitchen, then the laundry room, then the dining room. A while ago, Max and I decided that this room would be a study/library/office type space (since there’s a much larger living room right across the hall), but we’ve since sort of switched gears on that. Realistically, the “big living room” is probably a couple years off—even though I’m dying to get to it, it’s low on the priority list. I don’t want to wait that long to have some kind of space to sit and hang out and entertain, though, so I want this to be the living room for now! It’ll still house the books (or most of them, anyway), but also a couch and a couple chairs and stuff like that. I’ve been working hard to get it done-ish before the cottage drags me back into its clutches.

ANYWAY. I’ve talked about this before, but one of my big conundrums with this room was the feeling that there was something missing. The wall that the room shares with the dining room is bumped-out, and there’s this narrow/shallow little closet on the side that I’ve been informed is called a chimney cupboard, and would have been used for wood storage and whatnot. You can kind of tell from the crappy picture above (taken at our first walk-through) that there’s a large patch in the floor in front of this wall, and that the baseboard ends abruptly.

I’m not sure exactly what was here originally, but I have a couple reasonable guesses. There’s a chimney behind the wall (which has since been dismantled below the roof line, so doesn’t actually do anything), and a vent hole up near the ceiling. The floor patch indicates that there was some kind of stone hearth set into the floor here, and likely a wood-burning stove sitting on top of that. Our house was built around 1865, and since radiators didn’t come into use until the end of the century (and could have been installed here as late as the 1920s, perhaps), wood stoves would have been the original heat source. As for a mantel, it’s anyone’s guess. There’s a beautiful marble one in the big living room, but whatever used to live on this wall has been gone for a long time.

Given all of this, I had this big idea. Why not put something back in that spot? Even if it didn’t actually serve a functional purpose, a proper-looking fireplace would go a long way toward anchoring the room and providing some nice ambiance. The fireplace in our apartment is purely ornamental, but just the fact that it’s there gives the room so much. So that is what I set out to do. Fake fireplace plan: a-go.

A quick word about the fakey-ness of it all: I feel so weird about this kind of thing! I sort of think of myself as a modernist renovating an old house, and this kind of thing feels distinctly not-modernist. It’s the same feeling I get about putting up a bunch of foam ceiling medallions (which I’ve faux-aged on top of it!) or trying to recreate original molding work like I did in the laundry room. What’s so wrong with new work looking…new? Isn’t there something much more honest and authentic about just embracing all the original detail that does remain in this house, and allowing the new work and materials to just be what they are? I don’t know. I think about it a lot. But at the end of the day, I guess I want the house to seem more impeccably preserved than it actually is, for better or worse. So I’m going with it!

atjohnshouse

SO, now that I’ve written like 700 words and bored you to tears, let’s get into how this faux-fireplace party went down. It started with this mantel. Back in MAY. Yeah, this took a while from start to finish. My wonderful and insanely talented friend, John, ripped this mantel out of his house during his own renovation, but had stashed it in his basement instead of tossing it. His house was built in 1723, and this mantel was fabricated and added in the 1920s. I’d say John’s renovation sensibility is a bit more purist than mine, so he worked with a woodworker to custom build a more period-accurate mantel to replace this one (which is gorgeous, by the way). So anyway…John had a mantel, I needed a mantel, John didn’t want any money for it, I like free things…it worked out.

wallopeneduo

When I got the mantel home, I opened up the part of the wall where the old mantel would have theoretically been, wondering if I’d find a firebox or just the chimney. Just the chimney! Since there wasn’t any depth to work with inside the wall, whatever would go on the inside of the mantel had to be essentially flush with the wall. Hmmm. Hmmmmmmm.

mantelinplaceish

I dragged the mantel into place-ish (Linus assisted), just to get a sense of how it would look and feel. Even though this thing is quite a bit newer than my house, I feel like it plays really nicely with our moldings. As you can tell from the floor patch, it’s about a foot or so wider than what was here originally, which is something I sort of fretted over before deciding to just go with. I really didn’t want to get into trying to hack the mantel down to the “right” size (I liked the proportions of it as-is), and I really liked the idea of using this mantel in particular because I had it, I didn’t have to pay for it, and I liked the whole story behind it. Something new or salvaged just wouldn’t have held the same meaning to me.

hearthcutout

So, onwards! I removed the old patch job with no real plan about what was to go in its place, but sometimes you just need to dive in and figure it out later.

guttedwall

Unfortunately, this plaster wall was just beyond the point of trying to salvage. The plaster had separated a lot from the lath, it had some very significant cracks, and had undergone some failed repair attempts over the years with lots and lots of joint compound but nothing (like mesh tape, plaster buttons, or screening) to stabilize the plaster from further shifting. Even though I want to save as much of the original plaster walls in the house as possible, the best course of action here was to just start over, so that’s what I did!

lathshims

Since new 1/2″ drywall wouldn’t match the original depth of the plaster walls, I experimented with reusing the original lath strips, this time nailed directly onto the wall framing. I could have also just left all of the lath in place, but I’d already taken it down and this allowed me to still salvage the bulk of it for some other use down the road. I have no idea what to do with all my lath, but I’ll come up with something!

drywallinplace

Putting up the new drywall was no big thing. Since the underlying framing wasn’t very smooth, the drywall wasn’t either—but I had a plan! I actually wanted it to be a little irregular to mimic the look of the other plaster walls.

drywalled

I used fiberglass mesh tape and joint compound to cover the seams and screw holes. You typically do three coats of joint compound with new drywall and then finish off with a fine sanding before paint.

skimcoatingwall

I wanted to experiment with getting more of an authentic plaster look, though, so I opted to skim-coat the entire wall with joint compound. I just used the pre-mixed all-purpose stuff, and I wasn’t too careful about it: I wanted the thickness of the skim-coat to vary slightly along the surface of the wall. In some places it’s barely there at all, and in some places it’s probably about 1/8″ thick.

skimcoatedwall

Here’s a terrible picture of the whole wall skim-coated. The whiter spots are where the joint compound is thinner and dried faster. It doesn’t look at all like a textured wall or anything—it’s just very very subtly uneven so that it doesn’t stand out as looking flat and new. I sanded it all before painting and it really is indistinguishable from the plaster. Yay!

marble

Ok, moving on…one of the big challenges was figuring out the material for the hearth. There were a few options here. Sometimes, like in our apartment fireplace, you’ll see a tiled hearth—but tile is tough to pull off without the whole thing looking brand new. New tile isn’t made the same way as old tile and doesn’t have the same character, so I’d either have to get really spendy reproduction tile or find something salvage. What I thought I really wanted, though, was a nice slab of honed marble. I mean, what’s more classic and pretty than marble, right? Since the size I needed was somewhat irregular (about 75 inches with a flexible depth, ideally between about 16-24 inches) I thought maybe I could find something cheap-ish in the remnant section of a stone yard.

Wrong! I took myself to a local stone place (that mainly does countertops and stuff) and found this really gorgeous slab. It was honed, it was about the right size, and it was even a little damaged along the edges and had a couple scratches, which I sort of liked. But then it priced out at over a thousand dollars, so I burst into tears and ran away. Soapstone was even more expensive, and granite was a little cheaper but still too much money, and I didn’t want granite at all anyway.

bluestone

Then it dawned on me: what about good old Kingston bluestone? I suppose it’s even possible that that’s what was here originally, but who knows. I could probably find something that was locally quarried, super pretty, and much cheaper than marble or soapstone. It would reference Kingston history and even sort of tie into the exterior of the house, which is lined with bluestone sidewalks and pathways.

It just so happens that John, the same friend who gave me the mantel, worked for a couple of years as a stone mason when he first moved up here. My friends, bear in mind that this man is an optometrist. Almost 15 years ago at this point, he decided to take a break from optometry, pretty much just for the sake of learning something awesome that he felt passionate about, and I guess that thing was building stone walls and stuff. He worked as an apprentice under a stone mason named Sean Fox. So when I mentioned wanting bluestone, John knew who to call!

Sean was awesome to work with. I told him what I was doing and what I wanted, and he helped me find slabs that were good options. He also has the cutest German Shepherd named Dante, who is modeling the slab that I chose! The slab was thicker than I anticipated (Sean said that a thinner slab was likely to crack either during transport or once it was in place) and cost $400, which I figured was reasonable. I don’t know if I could have found the stone cheaper elsewhere, but at that point I was excited to have found something I liked and from somebody who understood what I was after. They had to cut the slab down slightly to fit my dimensions, and then burned the edges just a bit. I didn’t want it to look machine-cut, but I also didn’t want it to look overly rustic and rough-hewn, either. He did a perfect job, and I got to pick it up a week later.

FYI, bluestone is HEAVY. I don’t know how much this thing weighed, but I’d guess around a thousand pounds. Seriously! Sean loaded it into the back of John’s pick-up with a forklift, but it was up to me to figure out how to get it into my house and in place on the other end. Yikes! So one day, I finagled all of the people working over at Bluestone Cottage to take a break and walk over to my house to help with this thing. The whole ordeal was VERY STRESSFUL. I don’t have any pictures because I was helping and also shielding my eyes and generally terrified that the whole thing would go crashing through the floor and down into the basement and the whole house would collapse. But between about 6 guys, we were able to get it inside and into place and it wasn’t even as horrible as anticipated. I had to cut out a little more of the floor beforehand, but that wasn’t a big deal.

summercover

With the mantel in my possession and the hearth in the floor (and not going anywhere, ever), I still had to figure out how to sort out the space inside the mantel. I really fly by the seat of my pants, evidently! John actually gave me some cast iron insert parts that were with the mantel back at his house, but they were designed for a firebox and wouldn’t work here, since the wall doesn’t actually have any depth. I really needed something that would cover the entire surface and give the illusion of depth behind it without actually requiring it.

Enter: the fireplace cover! I went to one of the salvage places in town and found this big old rusty cast iron beauty. It isn’t so hard to find the arched (or sometimes rectangular) surrounding part, but the summer cover that goes inside it (exactly what it sounds like—a decorative cover to conceal the firebox in the months when the fireplace wouldn’t be in use) is a bit more rare—and finding the two together is even more challenging! I got really lucky that this one was waiting for me. The dimensions were perfect, and the detailing is just gorgeous! It’s definitely very Victorian (my house is more Greek Revival—in other words, pre-Victorian), but I love it all the same. It came home with me for $150, which is more than I wanted to spend, but after some poking around online seems to be a steal of a deal.

drywalltracing

OK, so! Mantel—check! Hearth—check! Summer cover—check! The next decision was AGONY. What to put between the inside edges of the mantel and the summer cover? Usually I’m pretty decisive with this stuff, but this whole project seemed so full of unknowns and opportunities to royally fuck everything up and end up with something that looked super dumb and super faux and lame and I was very afraid of that happening. The idea of tile was kind of nice, but it was the same issue with the hearth—new tile would result in the whole thing looking new and kind of cheesy, and vintage or repro tiles are so hard to come by and so expensive, and I’d already spent way more money (remember, I’m $550 deep at this point!) on this project that is purely aesthetic and was supposed to be essentially free. Then I went through this long phase where I thought about doing brick veneer tiles and painting them, but I eventually got over it and nixed that idea. I became mildly obsessed with old fireplaces everywhere I went—studying them to figure out what would look authentic and be feasible, and what I landed on was a plastered treatment. You see this a lot in old houses—maybe a brick surround that’s been plastered over and painted. Often the hearth is also painted, but I wasn’t about to slap paint on my bluestone!

So anyway. More faux. I turned the mantel around, screwed a scrap piece of 1/2″ drywall in through the back, and traced the outer edges of the cover with a sharpie. The inner part of the cover is deeper than the outer part, if that makes sense, so the outside needed a lip to sit flush with, while the inside needed a little space behind the face of the drywall. I have no idea if I’m explaining this well. Then I took a drywall knife and cut an inch or two inside my sharpie line and removed the inner piece. Then I (finally!) moved the mantel into place and secured it to the wall by screwing a few 4″ screws through the front and into studs. Then I simply patched the holes (I like Ready Patch for small things like this—it sands down smoother than wood putty) and caulked the places where the mantel meets the wall. Then I just had to patch in a few floor boards and the original molding that I pried off and saved way back when I started this whole rigamarole.

roughskimcoat

Since drywall is so flat and smooth, I used more joint compound to create the faux plaster effect. I was very liberal with it—sort of slathering it on with a 6″ putty knife, intentionally creating and leaving ridges and imperfections along the way. You can sort of tell from the picture how the texture looks, but it wasn’t super evident until I got to the painting step. Anyway, once everything had about 36 hours to dry, I gave it the lightest sanding and moved on.

wirecupbrush

Because the summer cover had been sitting outside for so long at the salvage place and was covered in rust, I used this wire brush attachment on my drill to clean up the surface and prepare it for paint. These things are great for stuff like this! Then I went back in with a regular wire brush to get in the nooks and crannies of the pattern. I’d say all the prep took maybe an hour, and then I just wiped it down with a damp microfiber cloth and let it dry.

coveron

Securing the cover ended up being easier than anticipated. Before I put the whole thing in place, I painted a piece of drywall black and screwed that into the studs, so that you don’t see the framing through the holes in the summer cover pattern. Because the summer cover interlocks with the outer part, all I did to secure the whole assembly was use existing holes in the summer cover pattern. I drove two large screws into the studs behind—you can sort of see the screws in the picture above. The heads are sunk into the existing holes in the pattern, and after the paint, you have to really search for them. Nobody will ever notice except me. And everyone I tell.

painting

FINALLY, PAINT TIME! I had about half a can of high-gloss black oil paint from the failed kitchen floor experiment of yore, and so I broke it out here. This makes the project, as far as I’m concerned. The gloss black accentuates the texture of the faux-plaster business and the intricacy of the summer cover, but I think keeps everything looking understated and classic and pretty. Oil paint is so nice to work with once in a while for small stuff like this—there’s really nothing like it. After this first coat, I caulked at the transition between the cover and the faux-plastered surround and then painted a second coat. The finish is so hard and smooth and pretty. I’m thrilled with how it turned out!

fireplace3

ANNNNDDDDD, DONE. I love it. I really do. It completely changes the room. I don’t feel like it dominates, but it does provide a focal point and just a certain ambiance that was missing before. And I feel like it just fits—like you’d never walk into the house and think it was added recently or even really pay a lot of attention to it at all. That’s exactly what I wanted.

Fireplace2

I’m happy with the way it ended up fitting on the wall, too! Even though it’s a little wider than whatever was here originally, I don’t think it feels out of place or two big for the room.

I love the bluestone, but I do keep wondering what would happen if I tried to darken it up a little bit. I’m sort of afraid to touch it because I don’t want to ruin it, but I wonder if mineral oil would have the same kind of effect on this that it does on soapstone? I don’t know. I’ll live with it for a while and see how I’m feeling some other time.

I’m resisting showing wider shots of the room because it’s actually almost done! Told you I’ve been working hard. There are still a few major items to check off the to-do list, but I’m super excited about the way it’s coming together. It’s so weird and exciting to have this whole other usable space in the house! I can’t wait!

Back to Top